Series/Parallel Resistor Network Calculator

Combine resistors into series or parallel groups. The editor supports 16 resistors and four connection levels below the root. This tool cannot solve bridge circuits or arbitrary wiring.

Enter 0 Ω or a resistance from 1e-12 to 1e12 Ω. Use decimal or scientific notation. Changing a unit reinterprets its number.

Equivalent resistance

Complete every resistor value to see the network result.

Schematic, not to scale

Show the steps

Interactive calculation is unavailable until JavaScript loads. The formulas, worked examples and references below remain available.

Combine groups of resistors in a defined series/parallel topology. Calculate combined resistance and group reductions for electricity and circuit analysis.

How to use

Enter each resistance. Choose Ω, kΩ or MΩ beside each value.

Choose Series or Parallel for each group. Add a resistor or a group to build the network.

Use Add in series or Add in parallel beside a resistor to nest it. The new group keeps the original resistor and adds an empty resistor.

Read the whole-network equivalent resistance. Select a group from Group to inspect. Open Show the steps to see reductions from inner groups outward.

Remove a resistor or group when it is absent from your intended circuit. A group with one remaining child collapses to that child.

Copy result includes the connection structure and total. Reset clears the network and restores the initial two-resistor group.

Science

The editor represents a network as two-terminal pieces. Series groups add their child equivalents. Parallel groups combine inverse equivalents. The tool reduces nested groups from the inside outward.

A zero-ohm resistor models an ideal wire. It adds nothing in series and shorts a parallel group containing it. A short inside one group does not automatically short resistors outside that group.

Some circuits cannot be reduced this way. Bridges and connections shared between groups require circuit-analysis methods beyond this editor's tree structure.

The model assumes fixed ideal resistance and negligible wire resistance. It does not calculate tolerance, temperature, supply limits or power ratings. The drawing describes connections and is not to scale.

Enter 0 Ω or a resistance from 1e-12 to 1e12 Ω. The network can contain up to 16 resistors and four connection levels below the root. Binary64 arithmetic approximates decimal entries and does not improve measurement accuracy.

In the formulas, E is equivalent resistance in ohms and n is the number of children in a group. The symbols + and ∥ denote series and parallel connections. They are not an input expression language.

Formulas

Resistor leaf: E(R) = R

Series group: E(S) = E1 + E2 + … + En

Positive parallel group: E(P) = 1 / (1/E1 + 1/E2 + … + 1/En)

Parallel short: If a validated child has E = 0 Ω, its parallel group has E = 0 Ω.

Prefixes: 1 kΩ = 1000 Ω. 1 MΩ = 1,000,000 Ω

Examples

(100 Ω ∥ 100 Ω) + 50 Ω: 100 Ω. The parallel group reduces to 50 Ω. Add the series 50 Ω.

(100 Ω + 200 Ω) ∥ 300 Ω: 150 Ω. The series branch is 300 Ω, in parallel with another 300 Ω.

1 kΩ + (2 kΩ ∥ 3 kΩ): 2.2 kΩ. The inner group is 1.2 kΩ. Add 1 kΩ.

(0 Ω ∥ 100 Ω) + 50 Ω: 50 Ω. The shorted inner parallel group contributes zero in series.

(0 Ω + 100 Ω) ∥ 200 Ω: 200/3 Ω ≈ 66.66666667 Ω. Zero in series leaves 100 Ω. That branch is not a short.

A single 4.7 kΩ resistor: 4.7 kΩ. With no groups, the equivalent is the resistor itself.

References

OpenStax University Physics Volume 2, section 10.2: Resistors in series and parallel

OpenStax University Physics Volume 2, section 10.3: Kirchhoff's rules

BIPM: SI prefixes