Heat-sink thermal-resistance calculator

All thermal resistances are in °C/W, as data sheets and heat-sink catalogues give them.

Use the data-sheet maximum, or a lower design target for margin.

From the device's data sheet.

Grease, pad or insulating washer; check its data.

Use θ_JA for this device on your board, without a heat sink.

Enter the power, temperatures and θ_JC and θ_CS to see the heat sink you need.

Show the steps

Interactive calculation is unavailable until JavaScript loads. The formulas, worked examples and references below remain available.

Find the largest heat-sink-to-ambient thermal resistance that keeps a junction below its limit, from power, ambient temperature and junction-to-case and interface resistance.

How to use

Enter the power the device dissipates, its ambient temperature and the junction limit or a lower design target.

Enter θ_JC from the device's data sheet and θ_CS for the grease, pad or insulating washer.

Read the maximum θ_SA. Choose a heat sink rated at or below that value at the expected airflow and power.

If the device's θ_JA on your board is known, include the board path to see how it changes the heat-sink requirement.

Copy the labelled result or reset the inputs to their starting values.

Science

The allowed temperature rise, junction limit minus ambient, divided by the power is the whole thermal budget in °C/W. Heat leaves the junction through θ_JC into the case, through the interface θ_CS into the heat sink, and through θ_SA into the air. In series, these resistances add, so the heat sink may use what remains after θ_JC and θ_CS.

If θ_JC and θ_CS already use the whole budget, no heat sink can hold the limit. Reduce the power, choose a part with lower θ_JC, improve the interface or accept a lower ambient. An insulating washer can cost more than a degree per watt on its own.

Some heat also leaves through the circuit board. When the device's θ_JA on your board is known, TI's SPRA953 combines the two paths in parallel. The heat sink can then be worse, and at low power the board alone may be enough.

Limitations: catalogue θ_SA depends on airflow, orientation and the power itself, so leave margin. The model assumes one device, a uniform heat-sink temperature and steady power. It does not design fins or fans, and pulsed loads need transient thermal data. Estimate interface resistance as thickness ÷ (conductivity × area), but measured values are better.

Formulas

Allowed rise and budget: θ_budget = (T_J,max − T_A) / P.

Heat sink in series: θ_SA,max = θ_budget − θ_JC − θ_CS.

With the board path: X = θ_JA × θ_budget / (θ_JA − θ_budget); θ_SA,max = X − θ_JC − θ_CS; no heat sink is needed when θ_budget ≥ θ_JA.

Interface estimate: θ_CS ≈ t / (k × A).

Examples

15 W, 40 °C ambient, 150 °C junction limit, θ_JC 0.5 and θ_CS 0.3 °C/W: θ_SA ≤ 6.533 °C/W; sink 138 °C and case 142.5 °C at the limit. The 110 °C rise gives a total budget of 7.333 °C/W. The case and interface use 0.8 °C/W.

100 W, 25 °C ambient, 145 °C limit, θ_JC 0.8 and θ_CS 0.1 °C/W: θ_SA ≤ 0.3 °C/W; sink 55 °C and case 65 °C. This is the high-power TO-3 example in TI SBOA021, solved for the heat sink.

50 W, 40 °C ambient, 125 °C limit, θ_JC 1.5 and θ_CS 0.5 °C/W: No heat sink can hold the limit; short by 0.3 °C/W. The budget is 1.7 °C/W, less than the 2 °C/W used by the junction-to-case and interface path.

5 W, 25 °C ambient, 125 °C limit, θ_JC 2, θ_CS 0.5 and board θ_JA 62 °C/W: θ_SA ≤ 27.02 °C/W; series-only requirement 17.5 °C/W. The board carries part of the heat, so the parallel-path model allows a higher sink resistance.

Using a data-sheet θ_JA as the heat-sink path: The data-sheet θ_JA already includes its test board and no heat sink. Use θ_JC for the junction-to-case part of the heat-sink path, as SPRA953 explains.

References

Texas Instruments SPRA953: Semiconductor and IC Package Thermal Metrics

Texas Instruments SBOA021: Heat Sinking — TO-3 Thermal Model

ROHM 65AN117E: How to Use the Thermal Resistance and Thermal Characteristics Parameters