Ohm's Law and Power Wheel

Magnitude. Use zero or a positive value. Resistance must be greater than zero. Select units beside each value.

Extra readings are checked against the selected pair within 0.1%. They do not replace the pair or estimate measurement uncertainty.

Complete the selected readings to calculate.

Ideal passive resistor at one fixed operating condition. DC magnitudes only.

Ohm's law quantity wheelA schematic with voltage, current, resistance and power. The result rows and equation route give the values and their provenance.VVoltage★ICurrent★RResistance★PPower★

Schematic. A star marks the main result. The wheel marks given and calculated quantities.

Enter two independent values.

Show the steps

Interactive calculation is unavailable until JavaScript loads. The formulas and worked examples below remain available.

Find voltage, current, resistance and power from two known values for a passive DC resistor, with optional checks for extra readings.

How to use

Choose the two quantities you know: voltage, current, resistance or power.

Enter both values. Select their units. Use positive resistance and nonnegative magnitudes for the other quantities.

Choose the main result. Read all four quantities. Each is marked Provided or Calculated.

To check another reading, enable Check extra readings. Enter the reading. A disagreement above 0.1% requires correction. The selected pair still determines the solution.

Read the equation route below the wheel for the selected formulas. Open Show the steps to see the substitutions. The wheel has no interactive controls.

Copy result includes inputs, units and assumptions. Reset clears all readings and restores the starting pair and result selection.

Science

Ohm's law relates voltage, current and resistance for an ohmic component at a fixed operating condition. Changing temperature or using a nonohmic device can change that relationship. This tool uses a single resistance value.

Electrical power combines voltage and current. Substituting the resistance relationship gives other power formulas. The equation route below the wheel shows the formulas used for the selected pair. Two suitable quantities determine the remaining quantities under this model.

This tool uses magnitudes. It does not model reference directions, generated power, phase differences, reactive components or AC impedance. A positive resistance represents a passive resistor. An ideal short or open circuit needs different limiting rules.

Zero can be a valid operating point when resistance is known. Zero applied voltage means zero current and zero power. If voltage and current are both zero while resistance is unknown, many resistances are possible and the answer is not unique.

Optional readings test agreement with the two selected values. The fixed 0.1% threshold checks numerical consistency. It does not assess specification tolerance or measurement uncertainty. The calculator does not select a safe component power rating.

Formulas

Voltage: V = I×R · V = P/I · V = √(P×R)

Current: I = V/R · I = P/V · I = √(P/R)

Resistance: R = V/I · R = V²/P · R = P/I²

Power: P = V×I · P = I²×R · P = V²/R. Use only expressions with defined denominators. V is voltage in volts, I current in amperes, R resistance in ohms, and P power in watts.

Examples

12 V and 2 A: 6 Ω and 24 W. Divide voltage by current for resistance. Multiply them for power.

5 V and 1 kΩ: 5 mA and 25 mW. Convert 1 kΩ to 1,000 Ω before calculating.

8 Ω and 2 W: 4 V and 0.5 A. The positive square roots give the supported magnitude solution.

0 V and 100 Ω: 0 A and 0 W. A known positive resistance permits a unique zero operating point.

0 V and 0 A: No unique resistance. Select a pair that includes resistance to describe this zero-power case.

12 V, 2 A, extra check 10 Ω: Inconsistent reading. The selected pair predicts 6 Ω. The 10 Ω reading does not agree within 0.1%.

References

OpenStax University Physics Volume 2, 9.4: Ohm's Law

OpenStax University Physics Volume 2, 9.5: Electrical Energy and Power