Slice Engineering: Filament Drying Desiccant
Need Support? Click Here
Free Delivery Above ₹999

Best seller

Slice Engineering

Filament Drying Desiccant

SKU: 3D5014

₹ 1,749.99 ₹ 1,999.99

In stock | Ready to ship

⚠ Only a few left in stock. Order soon.
⏱ High demand right now.
📦 Min order 1
Chat with us on WhatsApp We reply quickly! Contact Us
Filament Drying Desiccant₹ 1,749.99
Ask AI about this product
Open in ChatGPT Open in Claude Open in Gemini

Wet 3D printing filament can cause all sorts of issues. In fact, many of the issues that hotends or nozzles get blamed for can actually be traced back to filament that has absorbed too much moisture. Our facility is located in humid Florida, so we set out to find an easy way to keep the humidity from killing our prints. The Filament Drying Desiccant was the result. 
  • Activated alumina desiccant is 10x more powerful than comparable silica gel, and is non-toxic!
  • Creates enough of a relative humidity (Rh) gradient to absorb both surface moisture and water particles captured inside the filament
  • Stainless steel canister is perfectly sized to fit in the center of your filament spool
  • Desiccant is infinitely rechargeable in the stainless steel container
  • Made in USA!

To use simply remove the outer shrink wrap and pop off the cap, then insert the canister into the center of your filament spool. Store the spool in an airtight container and watch the humidity drop! More information can be found here.

NOTE: Desiccants work by absorbing moisture in their surroundings. The Filament Drying Desiccant is super good at this job, but even it will get saturated with water molecules eventually. To recharge it, simply toss the whole canister into an oven at 200 °C or more for 2 hours to remove the water. DO NOT MICROWAVE.

Please contact us for filament and desiccant drying service.

Want to see testing to verify our Filament Drying Desiccant is as amazing as we say it is? Check out our Desiccant Activation Testing White Paper!

Don't think wet filament is a problem? Take a look at Stefan's (CNC Kitchen) video on the topic:

 

    How do I install and use the Filament Drying Desiccant?
    Remove the outer shrink wrap, pop off the cap, and insert the canister into the center of your filament spool. Store the spool in an airtight container to maintain low humidity.
    What makes this desiccant more effective than silica gel?
    Activated alumina desiccant is 10x more powerful than comparable silica gel and is non-toxic.
    How do I recharge the desiccant after it becomes saturated?
    Toss the whole canister into an oven at 200 C or more for 2 hours to remove the water; do not microwave.
    Where should the desiccant be placed and how does it fit on the spool?
    The stainless steel canister is perfectly sized to fit in the center of your filament spool; after use, store the spool in an airtight container.
    Is there additional information or services available?
    Made in USA. You can view the Desiccant Activation Testing White Paper and contact us for filament and desiccant drying service.
    A
    Admin
    Welcome to the discussion thread for Filament Drying Desiccant
    Feel free to ask questions, share tips or report issues.

    Discover More In:

    3D Accessories, Nozzles & Glue → Clearance Sale → Slice Engineering | Official Page →

    Category: View all 3D Printer Products

    Fill out the form below and our team will get back to you with bulk pricing.

    Description
    Ask AI about this product
    Open in ChatGPT Open in Claude Open in Gemini

    Wet 3D printing filament can cause all sorts of issues. In fact, many of the issues that hotends or nozzles get blamed for can actually be traced back to filament that has absorbed too much moisture. Our facility is located in humid Florida, so we set out to find an easy way to keep the humidity from killing our prints. The Filament Drying Desiccant was the result. 
    • Activated alumina desiccant is 10x more powerful than comparable silica gel, and is non-toxic!
    • Creates enough of a relative humidity (Rh) gradient to absorb both surface moisture and water particles captured inside the filament
    • Stainless steel canister is perfectly sized to fit in the center of your filament spool
    • Desiccant is infinitely rechargeable in the stainless steel container
    • Made in USA!

    To use simply remove the outer shrink wrap and pop off the cap, then insert the canister into the center of your filament spool. Store the spool in an airtight container and watch the humidity drop! More information can be found here.

    NOTE: Desiccants work by absorbing moisture in their surroundings. The Filament Drying Desiccant is super good at this job, but even it will get saturated with water molecules eventually. To recharge it, simply toss the whole canister into an oven at 200 °C or more for 2 hours to remove the water. DO NOT MICROWAVE.

    Please contact us for filament and desiccant drying service.

    Want to see testing to verify our Filament Drying Desiccant is as amazing as we say it is? Check out our Desiccant Activation Testing White Paper!

    Don't think wet filament is a problem? Take a look at Stefan's (CNC Kitchen) video on the topic:

     

      FAQ
      How do I install and use the Filament Drying Desiccant?
      Remove the outer shrink wrap, pop off the cap, and insert the canister into the center of your filament spool. Store the spool in an airtight container to maintain low humidity.
      What makes this desiccant more effective than silica gel?
      Activated alumina desiccant is 10x more powerful than comparable silica gel and is non-toxic.
      How do I recharge the desiccant after it becomes saturated?
      Toss the whole canister into an oven at 200 C or more for 2 hours to remove the water; do not microwave.
      Where should the desiccant be placed and how does it fit on the spool?
      The stainless steel canister is perfectly sized to fit in the center of your filament spool; after use, store the spool in an airtight container.
      Is there additional information or services available?
      Made in USA. You can view the Desiccant Activation Testing White Paper and contact us for filament and desiccant drying service.
      Reviews
      Forum
      A
      Admin
      Welcome to the discussion thread for Filament Drying Desiccant
      Feel free to ask questions, share tips or report issues.
      Similar Products

      Discover More In:

      3D Accessories, Nozzles & Glue → Clearance Sale → Slice Engineering | Official Page →

      Category: View all 3D Printer Products

      Bulk Order

      Fill out the form below and our team will get back to you with bulk pricing.

      Custom Requirements?

      Meet with our team

      Related products

      Related products

      0106-14

      Waldom Electonics

      0106-14

      ₹ 2,623.53