DRV8833 is a dual H-bridge motor driver IC that can be used for bidirectional control of two brushed DC motors at 2.7 V to 10.8 V. It can supply up to about 1.2 A per channel continuously and can tolerate peak currents up to 2 A per channel for a few seconds, making it an ideal driver for small motors that run on relatively low voltages. The board ships populated with SMD components, including the DRV8833, and adds a FET for reverse battery protection.
This board is very similar to our DRV8835 dual motor driver carrier in operating voltage range and continuous current rating, but the DRV8835 has a lower minimum operating voltage, offers an extra control interface mode, and is 0.1″ smaller in each dimension; we also carry a DRV8835 dual motor driver shield that is easy to use with an Arduino. The DRV8833 has a higher peak current rating (2 A per channel vs 1.5 A), optional built-in current-limiting, and no need for externally supplied logic voltage.
For a smaller, lower-cost, single-channel alternative to this driver, please consider our DRV8838 carrier, which offers a similar operating voltage range and current capabilities.
For higher-voltage alternatives to this driver, consider our A4990 and DRV8801 motor driver carriers.
Note - The color and the layout of the board may differ, but it is the same Motor Driver Module.
Features
Dual-H-bridge motor driver: can drive two DC motors or one bipolar stepper motor
Operating voltage: 2.7 V to 10.8 V
Output current: 1.2 A continuous (2 A peak) per motor
Motor outputs can be paralleled to deliver 2.4 A continuous (4 A peak) to a single motor
Inputs are 3V- and 5V-compatible
Under-voltage lockout and protection against over-current and over-temperature
Reverse-voltage protection circuit
Current limiting can be enabled by adding sense resistors (not included)
It was really great experience shopping at THinkRobotics. The package was delivered intime with timely updatesz updates about tracking of shipments.kuddos.
{"id":1650986319944,"title":"DRV8833 2 Channel DC Motor Driver Module","handle":"drv8833-2-channel-dc-motor-driver-module","description":"\u003cp\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eDRV8833 is a dual H-bridge motor driver IC that can be used for bidirectional control of two brushed DC motors at 2.7 V to 10.8 V. It can supply up to about 1.2 A per channel continuously and can tolerate peak currents up to 2 A per channel for a few seconds, making it an ideal driver for small motors that run on relatively low voltages. The board ships populated with SMD components, including the DRV8833, and adds a FET for reverse battery protection.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eThis board is very similar to our DRV8835 dual motor driver carrier in operating voltage range and continuous current rating, but the DRV8835 has a lower minimum operating voltage, offers an extra control interface mode, and is 0.1″ smaller in each dimension; we also carry a DRV8835 dual motor driver shield that is easy to use with an Arduino. The DRV8833 has a higher peak current rating (2 A per channel vs 1.5 A), optional built-in current-limiting, and no need for externally supplied logic voltage.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eFor a smaller, lower-cost, single-channel alternative to this driver, please consider our DRV8838 carrier, which offers a similar operating voltage range and current capabilities.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eFor higher-voltage alternatives to this driver, consider our A4990 and DRV8801 motor driver carriers.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"text-decoration: underline;\" data-mce-style=\"text-decoration: underline;\"\u003e\u003cstrong\u003e\u003cspan style=\"color: #000000; text-decoration: underline;\" data-mce-style=\"color: #000000; text-decoration: underline;\"\u003eNote\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cstrong\u003e - The color and the layout of the board may differ, but it is the same Motor Driver Module.\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch3\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eFeatures\u003c\/span\u003e\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eDual-H-bridge motor driver: can drive two DC motors or one bipolar stepper motor\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eOperating voltage: 2.7 V to 10.8 V\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eOutput current: 1.2 A continuous (2 A peak) per motor\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eMotor outputs can be paralleled to deliver 2.4 A continuous (4 A peak) to a single motor\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eInputs are 3V- and 5V-compatible\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eUnder-voltage lockout and protection against over-current and over-temperature\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eReverse-voltage protection circuit\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eCurrent limiting can be enabled by adding sense resistors (not included)\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch5\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eSpecifications\u003c\/span\u003e\u003c\/h5\u003e\n\u003cp\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0014\/4313\/5560\/files\/d483d4a961b899074fb4dc9ec74d7c39_480x480.jpg?v=1593194208\"\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003ch5\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eResources\u003c\/span\u003e\u003c\/h5\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/github.com\/thinkrobotics\/DATASHEET\/tree\/master\/ELECTRONIC_COMPONENTS\/ELC4003\"\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eDatasheet\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/github.com\/thinkrobotics\/SAMPLE_CODE\/tree\/master\/ELECTRONIC_COMPONENTS\/ELC4003\"\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eSample Code\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e","published_at":"2022-12-06T11:23:06+05:30","created_at":"2019-03-04T07:15:58+05:30","vendor":"ThinkRobotics.in","type":"Motor Drivers","tags":["2 channel","driver","ELC4","motor drivers","MTR-DRV","servo motor drivers","STPR-DRV"],"price":8999,"price_min":8999,"price_max":9999,"available":true,"price_varies":true,"compare_at_price":33000,"compare_at_price_min":33000,"compare_at_price_max":40000,"compare_at_price_varies":true,"variants":[{"id":16231428980808,"title":"Without Soldered Pin","option1":"Without Soldered Pin","option2":null,"option3":null,"sku":"ELC4003","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"DRV8833 2 Channel DC Motor Driver Module - Without Soldered Pin","public_title":"Without Soldered Pin","options":["Without Soldered Pin"],"price":8999,"weight":10,"compare_at_price":33000,"inventory_management":"shopify","barcode":"16231428980808","requires_selling_plan":false,"selling_plan_allocations":[]},{"id":27847105740872,"title":"With Soldered Pin","option1":"With Soldered Pin","option2":null,"option3":null,"sku":"ELC4003S","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"DRV8833 2 Channel DC Motor Driver Module - With Soldered Pin","public_title":"With Soldered Pin","options":["With Soldered Pin"],"price":9999,"weight":10,"compare_at_price":40000,"inventory_management":"shopify","barcode":"27847105740872","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/thinkrobotics.com\/cdn\/shop\/products\/1_f7cced00-fc63-4bfd-96d7-3e5fee29a7e1.jpg?v=1577794074","\/\/thinkrobotics.com\/cdn\/shop\/products\/I.jpg?v=1577794074","\/\/thinkrobotics.com\/cdn\/shop\/products\/HTB1HleNb26H8KJjSspmq6z2WXXaz.jpg?v=1577794074","\/\/thinkrobotics.com\/cdn\/shop\/products\/2_17ca8da5-2d4e-4f5f-a8dd-7bb0d5318c50.jpg?v=1577794074","\/\/thinkrobotics.com\/cdn\/shop\/products\/20210819_124552.jpg?v=1629358238","\/\/thinkrobotics.com\/cdn\/shop\/products\/20210819_124630.jpg?v=1629358238","\/\/thinkrobotics.com\/cdn\/shop\/products\/20210819_124705.jpg?v=1629358238","\/\/thinkrobotics.com\/cdn\/shop\/products\/20210819_124822.jpg?v=1629358238"],"featured_image":"\/\/thinkrobotics.com\/cdn\/shop\/products\/1_f7cced00-fc63-4bfd-96d7-3e5fee29a7e1.jpg?v=1577794074","options":["Soldered"],"media":[{"alt":"DRV8833 2 Channel DC Motor Driver Module","id":866193604680,"position":1,"preview_image":{"aspect_ratio":1.071,"height":746,"width":799,"src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/1_f7cced00-fc63-4bfd-96d7-3e5fee29a7e1.jpg?v=1577794074"},"aspect_ratio":1.071,"height":746,"media_type":"image","src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/1_f7cced00-fc63-4bfd-96d7-3e5fee29a7e1.jpg?v=1577794074","width":799},{"alt":"DRV8833 2 Channel DC Motor Driver Module","id":866193834056,"position":2,"preview_image":{"aspect_ratio":1.068,"height":749,"width":800,"src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/I.jpg?v=1577794074"},"aspect_ratio":1.068,"height":749,"media_type":"image","src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/I.jpg?v=1577794074","width":800},{"alt":"DRV8833 2 Channel DC Motor Driver Module","id":866193899592,"position":3,"preview_image":{"aspect_ratio":1.084,"height":738,"width":800,"src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/HTB1HleNb26H8KJjSspmq6z2WXXaz.jpg?v=1577794074"},"aspect_ratio":1.084,"height":738,"media_type":"image","src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/HTB1HleNb26H8KJjSspmq6z2WXXaz.jpg?v=1577794074","width":800},{"alt":"DRV8833 2 Channel DC Motor Driver Module","id":866193932360,"position":4,"preview_image":{"aspect_ratio":1.071,"height":747,"width":800,"src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/2_17ca8da5-2d4e-4f5f-a8dd-7bb0d5318c50.jpg?v=1577794074"},"aspect_ratio":1.071,"height":747,"media_type":"image","src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/2_17ca8da5-2d4e-4f5f-a8dd-7bb0d5318c50.jpg?v=1577794074","width":800},{"alt":"DRV8833 2 Channel DC Motor Driver Module","id":21195060183126,"position":5,"preview_image":{"aspect_ratio":0.75,"height":4032,"width":3024,"src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/20210819_124552.jpg?v=1629358238"},"aspect_ratio":0.75,"height":4032,"media_type":"image","src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/20210819_124552.jpg?v=1629358238","width":3024},{"alt":"DRV8833 2 Channel DC Motor Driver Module","id":21195060215894,"position":6,"preview_image":{"aspect_ratio":0.75,"height":4032,"width":3024,"src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/20210819_124630.jpg?v=1629358238"},"aspect_ratio":0.75,"height":4032,"media_type":"image","src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/20210819_124630.jpg?v=1629358238","width":3024},{"alt":"DRV8833 2 Channel DC Motor Driver Module","id":21195060248662,"position":7,"preview_image":{"aspect_ratio":0.75,"height":4032,"width":3024,"src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/20210819_124705.jpg?v=1629358238"},"aspect_ratio":0.75,"height":4032,"media_type":"image","src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/20210819_124705.jpg?v=1629358238","width":3024},{"alt":"DRV8833 2 Channel DC Motor Driver Module","id":21195060281430,"position":8,"preview_image":{"aspect_ratio":0.75,"height":4032,"width":3024,"src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/20210819_124822.jpg?v=1629358238"},"aspect_ratio":0.75,"height":4032,"media_type":"image","src":"\/\/thinkrobotics.com\/cdn\/shop\/products\/20210819_124822.jpg?v=1629358238","width":3024}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cp\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eDRV8833 is a dual H-bridge motor driver IC that can be used for bidirectional control of two brushed DC motors at 2.7 V to 10.8 V. It can supply up to about 1.2 A per channel continuously and can tolerate peak currents up to 2 A per channel for a few seconds, making it an ideal driver for small motors that run on relatively low voltages. The board ships populated with SMD components, including the DRV8833, and adds a FET for reverse battery protection.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eThis board is very similar to our DRV8835 dual motor driver carrier in operating voltage range and continuous current rating, but the DRV8835 has a lower minimum operating voltage, offers an extra control interface mode, and is 0.1″ smaller in each dimension; we also carry a DRV8835 dual motor driver shield that is easy to use with an Arduino. The DRV8833 has a higher peak current rating (2 A per channel vs 1.5 A), optional built-in current-limiting, and no need for externally supplied logic voltage.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eFor a smaller, lower-cost, single-channel alternative to this driver, please consider our DRV8838 carrier, which offers a similar operating voltage range and current capabilities.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eFor higher-voltage alternatives to this driver, consider our A4990 and DRV8801 motor driver carriers.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"text-decoration: underline;\" data-mce-style=\"text-decoration: underline;\"\u003e\u003cstrong\u003e\u003cspan style=\"color: #000000; text-decoration: underline;\" data-mce-style=\"color: #000000; text-decoration: underline;\"\u003eNote\u003c\/span\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cstrong\u003e - The color and the layout of the board may differ, but it is the same Motor Driver Module.\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch3\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eFeatures\u003c\/span\u003e\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eDual-H-bridge motor driver: can drive two DC motors or one bipolar stepper motor\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eOperating voltage: 2.7 V to 10.8 V\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eOutput current: 1.2 A continuous (2 A peak) per motor\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eMotor outputs can be paralleled to deliver 2.4 A continuous (4 A peak) to a single motor\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eInputs are 3V- and 5V-compatible\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eUnder-voltage lockout and protection against over-current and over-temperature\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eReverse-voltage protection circuit\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eCurrent limiting can be enabled by adding sense resistors (not included)\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch5\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eSpecifications\u003c\/span\u003e\u003c\/h5\u003e\n\u003cp\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0014\/4313\/5560\/files\/d483d4a961b899074fb4dc9ec74d7c39_480x480.jpg?v=1593194208\"\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003ch5\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eResources\u003c\/span\u003e\u003c\/h5\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/github.com\/thinkrobotics\/DATASHEET\/tree\/master\/ELECTRONIC_COMPONENTS\/ELC4003\"\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eDatasheet\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/github.com\/thinkrobotics\/SAMPLE_CODE\/tree\/master\/ELECTRONIC_COMPONENTS\/ELC4003\"\u003e\u003cspan style=\"color: #000000;\" data-mce-style=\"color: #000000;\"\u003eSample Code\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e"}